Power
Factor Seminar (PQ-102)
CEU TYPE: Technical TRAINING CLASSIFICATION: Electrical
Maintenance IEPA#: 8021
WHY YOU SHOULD ATTEND THIS SEMINAR: The water industry consumes a considerable
amount of electricity to operate electric pump motors. In the USA, about two thirds
of electricity consumption is for the purpose of operating electrical
motors. For the water industry, the percentage is probably higher.
With electricity representing such a
significant portion of the operating costs, it makes sense to assure the most
effective use of the electrical resources. By improving power factor,
energy costs associated with low power factor may be eliminated.
Additionally, kVA demand charges may be reduced as can branch circuit conductor
power losses.
COURSE SUMMARY: As commercial and industrial companies continue to strive for greater energy efficiency, lower energy costs and better utilization of their electrical resources, knowledge of power factor has become essential for people in the electrical services industry. With the technological advances that have occurred in electrical and electronic equipment, power factor has grown into three types (displacement, distortion and total power factor). Only when all three are understood and addressed in the electrical system can maximum efficiency be attained. High total power factor can improve electrical system reliability, process & production equipment up-time, and reduce energy costs through elimination of power factor charges.
This four hour seminar course explains the three types of power factor, from a cause and effect basis and then teaches the intricacies of each type along with the methods to improve each power factor. The seminar demonstrates how to size power factor capacitors for various types of situations and the pitfalls to be avoided.
Several real life examples are worked as a group to demonstrate the techniques used to perform analysis of power factor, size power factor equipment and to quantify the expected results and ROI.
Upon completion of this course, participants should have a meaningful understanding of the various types of power factor, the impact that low power factor has on electric power systems, the causes of low power factor, methods to analyze power factor and methods to improve power factor.
This course is applicable to electrical industry professionals serving either industrial or commercial environments. For maximum benefit of this course, participants should have an understanding of basic electrical principles such as Ohms law, power, electrical metering, motors and general electrical equipment and systems.
COURSE OUTLINE:
- Introduction 15 minutes
- Definition of power factor
- Benefits of high power factor
- Problems with low power factor
- Types of Power Factor
- Fundamental Frequency (Displacement) Power Factor 150 minutes
- Motor currents and PF
- Typical PF by industry
- Lagging (inductive) current
- Leading (capacitive) current
- How much capacitance to add
- Harmonic resonance
- Detuning capacitors to avoid resonance
- Capacitor boosting (Voltage, kVAR, current)
- Local vs. Centralized capacitors
- Fixed vs. automatic PF capacitor systems
- Capacitor switching device ratings
- Cost of low power factor
- Distortion Power Factor 45 minutes
- Estimating distortion PF based on harmonic current distortion
- Causes of low distortion power factor (harmonic distortion)
- Typical current distortion by equipment
- What does harmonic current distortion look like?
- Improving distortion PF
- Total (true rms) Power Factor 30 minutes
- Function of both displacement and distortion PF
- Best practices
- Decisions to be made about total PF
INSTRUCTOR:
John Houdek, Allied Industrial Marketing John Houdek is president and co-owner of Allied Industrial Marketing,
Inc. (Cedarburg, WI, USA), a company that specializes in electrical
power quality. John serves the power quality industry as an un-biased
resource for a variety of power quality services including problem
diagnosis, harmonic analysis, filter design, computer simulation,
training and seminars as well as technical marketing support for key
components used for the assembly of high performance power quality
equipment.
Prior to forming Allied Industrial Marketing, John
held senior management positions for two electrical power quality
equipment manufacturers. John earned an MBA from Keller Graduate School
of Management in 1989 and has a bachelor’s degree in electrical
engineering technology from MSOE, where he is also a part time lecturer.
John
is an adjunct assistant professor at MSOE (Milwaukee School of
Engineering) where he teaches a course in electrical power quality. He
has presented power quality seminars and training programs throughout
North America, in Europe, Asia and South America and has authored many
technical papers which have been published or presented throughout the
world.
REGISTRATION & HOURS: Registration begins at 7:30am. The training will start at 8:00am and will conclude by 12:00pm. Earn up to 4 Professional Development Hours (PDH's) for engineers or Renewal Training Credit (RTC) hours for water operators. Continental breakfast will be included.
COST:
Registration Type
| ISAWWA Member Rate
| Non ISAWWA Member Rate
| Early Bird (ends 01/12/14)
| $32
| $48
| Regular (ends 01/21/14)
| $42
| $58
| After 01/21 or Onsite
| $52
| $68
|
THIS CLASS IS LIMITED TO FIRST 35 REGISTRANTS
|